Instytut Podstawowych Problemów Techniki

Streszczenie:

TiNi shape memory alloy (SMA) was subjected to tension at various strain rates for stress- and strain-controlled tests. The nucleation, development and saturation of the stress-induced martensitic transformation were investigated, based on the specimen temperature changes, measured by a fast and sensitive infrared camera. It was found that the initial, macroscopically homogeneous phase transformation occurs at the same stress level for all strain rates applied, regardless of the loading manner, while the stress of the localized transformation increases with the strain rate. At higher strain rate, a more dynamic course of the transformation process was observed, revealed in the creation of numerous fine transformation bands. An inflection point was noticed on the stress–strain curve, dividing the transformation range into two stages: the first heterogeneous, where transformation bands nucleate and evolve throughout the sample; the second, where the bands overlap, related to significant temperature increase and an upswing region of the curve. In the final part of the SMA loading a decrease of the average sample temperature revealed the saturation stage of the transformation. It was also observed that nucleation of the localized martensitic forward transformation takes place in the weakest area of the sample in both approaches, whereas the reverse transformation always initiates in its central part.

Słowa kluczowe:

shape memory alloy, various strain rates, stress- and strain-controlled tests, stress-induced martensitic transformation, fast and sensitive infrared camera, transformation bands, localized martensitic forward transformation, reverse transformation

Afiliacje autorów:

Streszczenie:

In this study, the thermomechanical coupling effects accompanying stress-induced martensitic transformation in TiNi shape memory alloy subjected to compression test were investigated. The mechanical characteristics were elaborated and the temperature changes related to the exothermic martensitic forward transformation and the endothermic reverse one were measured in a contactless manner by a fast and sensitive infrared camera. The obtained temperature changes of the specimen depend on the strain rate applied. At higher strain rate, greater temperature changes were observed, because the heat flow to the surroundings was lower and the process was closer to adiabatic conditions. The temperature changes of the shape memory alloy significantly influence its stressstrain characteristics. Moreover, the energy dissipated during a compression cycle was calculated for various strain rates. The study revealed that both the loading work and recoverable strain energy increase with increasing strain rate, while the dissipated energy fraction decreases.

Słowa kluczowe:

shape memory alloy, compression test, exothermic/endothermic transformation, infrared camera, energy dissipation

Afiliacje autorów:

Streszczenie:

TiNi shape memory alloy (SMA) specimens have been subjected to tension carried out at various strain rates. The goal was to investigate a nucleation and development of the stressinduced martensitic transformation by infrared (IR) and acoustic emission (AE) techniques. Therefore, both the infrared radiation and acoustic emission data were recorded using a fast infrared camera and acoustic emission set-up, respectively. It has been shown that the initial, macroscopically homogeneous transformation initiates in the elastic stage of the deformation even before the stress-strain curve knee and formation of the localized transformation bands. It has also been found that the homogeneous transformation occurs at similar stress level for all strain rates applied, while the localized martensitic transformation depends on the strain rate. Nucleation and development of the localized transformation bands, detected by the infrared camera, were confirmed by acoustic emission technique. The differences between the IR and AE activities were recorded during the TiNi SMA loading and unloading process, manifesting different dynamics of the stress-induced martensitic forward and reverse transformation.

Słowa kluczowe:

shape memory alloy, TiNi, superelasticity, martensitic transformation, tension test, acoustic emission

Afiliacje autorów:

Streszczenie:

This work compares the thermomechanical behavior of TiNi shape memory alloy subjected to the compression test performed under various strain rates. The mechanical characteristics of the material were elaborated. The specimen temperature changes related to the exothermic martensitic forward and endothermic reverse transformation were measured in a contact-less manner by a very fast and sensitive infrared camera. It has been found that in this experimental conditions the stress-induced transformation and reorientation processes occurred homogeneously, since the temperature distribution observed on the specimen surface was uniform. The obtained temperature variation depends on the strain rate applied. At the higher strain rate the higher temperature changes were obtained, because the heat flow to the surroundings was lower and the process was closer to adiabatic conditions. The temperature changes influence significantly the SMA stress-strain curves and their mechanical properties.

Słowa kluczowe:

shape memory alloy, various strain rates, compression tests, exothermic martensitic forward, endothermic reverse transformation, fast and sensitive infrared camera

Afiliacje autorów: