Instytut Podstawowych Problemów Techniki

Streszczenie:

AISI 304 steel experiences plastic flow instability during tension at room temperature if appropriate conditions are applied: a low strain rate and a sufficiently long gauge section of the sample. Then, propagation of the strain-localised band is activated. The electron backscattered diffraction (EBSD) research revealed that the reason is not only the difference in the content of the secondary phase – martensite α’ across the front face, but also the change in the volume fraction of austenite grains with Copper (Cu) and Goss-Brass (GB) orientation. Consequently, there is a division between two areas of high and limited deformation capacity. The tendency to maintain the continuity of deformation fields induces a massive rotation of austenite grains to Cu and GB orientations, which then undergo shearing and phase transformation. As a result, momentary strain accumulation leaves behind a stiffer zone. It is shown that the trapping of austenite grains prone to large deformations, inside the matrix with Cu and GB orientations, makes the formation of a plastic strain front possible. These features improve the ductility and strength of the 304 steel over 316L and 316LN at room temperature. The in-situ EBSD tension studies for the considered grades reveal three developing textures, with their comparison showing a gradual decrease in the preferences of the Cu and GB components. Thus, the appearing bands of the accumulated strains in 316L are limited by the Cu and GB areas, while such blockages do not occur in 316LN. The presented strengthening mechanism is confirmed by the digital image correlation (DIC) measurements. The root-mean-square (RMS) function of strains along the tensile direction, characterising the linear surroundings of the considered point, is introduced as a tool for linking the micro and macro scales. The experimental results provide a basis for explaining discontinuous front propagation at a temperature near 0 K.

Słowa kluczowe:

Plastic flow instability, Martensitic transformation, Austenitic stainless steels, RMS strain amplitude

Afiliacje autorów:

Streszczenie:

This paper presents a novel measurement method that aims to qualitatively and quantitatively assess uniform deformation during displacement- and force-controlled tensile tests of ductile metals. The method utilizes digital image correlation technology to record the strain distribution during tensile testing, followed by the calculation of the floating root mean square (RMS) value of the strain amplitude along the specimen axis. By implementing this approach, the RMS-based profiles of strain amplitude are identified in different metals and alloys, including austenitic stainless steels, structural steel, copper, and aluminium alloys. Moreover, the proposed method holds potential for predicting important deformation characteristics such as distribution of intensive plastic zones, necking effect, and delocalization effect. Thus, it establishes a link between macroscale and microscale during the analysis of plastic deformation behaviour. The effectiveness of the new method is compared with existing strain and strain-rate methods. The novel approach demonstrates promising advantages in the context of the identification of metal-forming parameters.

Słowa kluczowe:

Digital image correlation, Root mean square, Uniform strain distribution, Strain delocalization, Necking effect

Afiliacje autorów:

Streszczenie:

A remarkable plastic flow instability is observed during tensile deformation of the commercial 304 stainless-steel sheet at room temperature. It has been found that the occurrence of plastic flow instability in 304 is dependent on the strain rate and specimen gage length. Moreover, it is essentially the same as the necking caused by plastic instability in 316L. However, the enhanced strain hardening resulting from deformation-induced martensitic transformation facilitates the orderly propagation of the strain-localized band.

Afiliacje autorów:

Streszczenie:

The clip-on extensometers are recommended by international standards (ASTM E 1450-16 or ISO 6892-4:2015) for tension testing of structural alloys at 4 K. They are also frequently used to identify mechanical and electromechanical properties of superconducting wires or cables at cryogenic temperatures. In this study, the time responses of clip-on extensometers during uniaxial tensile tests of the engineering materials at liquid helium temperature are analysed. It turns out, that strong strain localization and self-excited vibrations of extensometers related to the plastic flow instability disturb the strain measurement. These measurement artefacts may affect the identification of the mechanical parameters, such as the 0.2% proof stress or the total elongation.

Słowa kluczowe:

clip-on extensometers, discontinuous plastic flow, strain localization, cryogenic temperatures, international standards

Afiliacje autorów:

Streszczenie:

Investigations by electron backscatter diffraction (EBSD) and X-ray diffraction with the use of synchrotron radiation, as well as parallel extended finite element (XFEM) simulations, reveal the evolution of the 316L stainless steel microstructure in the vicinity of a macro-crack developing at the temperature of liquid helium (4.2 K). The fracture propagation induces a dynamic, highly localized phase transformation of face-centred cubic austenite into α' martensite with a body-centred cubic structure. Synchrotron studies show that the texture of the primary phase controls the transition process. The austenite grains, tending to the stable Brass orientation, generate three mechanisms of the phase transformation. EBSD studies reveal that the secondary phase particles match the ordered austenitic matrix. Hence, interphase boundaries with the Pitsch disorientation are most often formed and α’ martensite undergoes intensive twinning. The XFEM simulations, based on the experimentally determined kinetics of the phase transformation and on the relevant constitutive relationships, reveal that the macro-crack propagates mainly in the martensitic phase. Synchrotron and EBSD studies confirm the almost 100% content of the secondary phase at the fracture surface. Moreover, they indicate that the boundaries formed then are largely random. As a result, the primary beneficial role of martensite as reinforcing particles is eliminated.

Słowa kluczowe:

austenitic steel, cryogenic temperatures, fracture process, fcc-bcc phase transformation, synchrotron radiation, electron backscatter diffraction, XFEM simulation

Afiliacje autorów:

Streszczenie:

In the present paper, the question of the mechanism of discontinuous plastic flow (DPF) occurring at extremely low temperatures (in the proximity of absolute zero), is for the first time raised in the context of kinematically controlled combined loads (independent control of displacement and rotation) and non-proportional loading paths. In order to identify the multiaxial stress state during DPF, a unique set-up for testing tubular samples under kinematically controlled traction and torsion in liquid helium (4.2 K) has been developed. The results of tests performed on grade 304 stainless steel thin-walled tubular samples subjected to combined loads (traction and torsion) in the proximity of absolute zero are for the first time reported. These novel results confirm the assumptions accepted when building the multiaxial constitutive model of discontinuous plastic flow, namely, the production of lattice barriers, the pile-ups of dislocations and the criterion of their collective failure, as well as the assumption that the serrations may be recorded by force and torque transducers independently. Thus, the numerically implemented model allows to reproduce the observed serrations, and to redistribute them between the loading directions.

Słowa kluczowe:

plasticity, discontinuous plastic flow, cryogenic temperatures, combined loads, non-proportional loading paths

Afiliacje autorów:

Streszczenie:

The strain induced martensitic phase stabilizes the propagation of macroscopic shear band during displacement-controlled uniaxial tensile test of metastable austenitic stainless steels (316 L, 304) at liquid helium temperature (4.2 K). It leads to huge Lüders-type deformation, high hardening and large ductility of the specimen. In Lüders range, shear band develops across the specimen in discontinuous and sequential way, which is reflected by stress oscillation on stress-strain curve and comb-like profile of temperature recorded during tests (so called discontinuous plastic flow - DPF). Based on the time responses of temperature and elongation transducers, a full picture of the localized deformation behaviour of specimen at 4.2 K was obtained, including its both spatial and temporal features. Moreover, the experimental results clarified that DPF has mechanical origin and it is accompanied by thermal effects. The model of temperature distribution during DPF was proposed. The model involves temperature effects driven by the elastocaloric phenomenon (experimentally identified at 4.2 K) and the plastic power dissipation. Based on the model, kinematic and thermal limits of DPF in the austenitic stainless steels were determined.

Słowa kluczowe:

discontinuous plastic flow, phase transformation, macroscopic shear band, thermomechanical processes, cryogenic temperatures

Afiliacje autorów:

Streszczenie:

Modern superconducting intermetallic materials (e.g. NbTi, Nb3Sn) are used to build conductors composed of a matrix and the superconductor strands. One of the most popular materials for matrix is copper, because of its excellent physical and mechanical properties at extremely low temperatures. Ductile OFE copper stabilizes, on one hand, the mechanical response of brittle superconductor strands and, on the other hand, takes over the electrical charge in case of quench (resistive transition). Thus, the composite structure of modern conductors used to build the coils of superconducting magnets is fully justified. Such a composite structure results in common deformation of the matrix and the strands when winding the coils and during the operation, when the coils are subjected to the prestress and to the Lorentz forces at extremely low temperatures (liquid or superfluid helium). When the loads are large enough, the copper-superconductor strands composite is subjected to inelastic deformation, including moderately large plastic strains. It is known, that copper and superconductor strands exhibit the so-called discontinuous plastic flow (DPF) at extremely low temperatures, that results in abrupt drops of stress against strain of different amplitude and frequency. In order to describe correctly the behaviour of composite superconductors at extremely low temperatures, a constitutive model of DPF has been developed and applied to both components: matrix and strands. The results of numerical analysis are compared with the experiments, carried out in dedicated cryostat containing liquid helium and the relevant instruments.

Słowa kluczowe:

superconductor, plastic deformation, cryogenic temperatures, constitutive model

Afiliacje autorów:

Streszczenie:

A popular class of materials massively used at cryogenic temperatures comprises the stainless steels of different grades, such as 304, 304L, 316, 316Ti, 316L, 316LN etc. Such materials are metastable at extremely low temperatures, and usually undergo plastic strain induced phase transformation. In addition, these materials applied in the proximity of absolute zero exhibit the so-called discontinuous (intermittent, serrated) plastic flow (DPF). It consists in frequent, abrupt drops of stress against strain, characterized by increasing amplitude of the stress oscillations. Strong coupling between both phenomena: DPF and phase transformation is observed. Recent experiments performed by means of stainless steel samples tested in liquid helium (4.2 K) clearly indicate strong strain localization during DPF, in the form of shear bands propagating along the sample. However, as soon as the phase transformation process takes place, the motion of shear bands is hindered by formation of secondary phase. A physically based constitutive model developed in the present paper reflects coupling between the discontinuous plastic flow and the plastic strain induced phase transformation in the temperature range 0–T1. The model involves nonlinear mixed hardening, that occurs during the 2nd stage of each serration (stress–strain oscillation). The hardening is based on two mechanisms: interaction of dislocations with the inclusions of secondary phase, evolution of tangent stiffness operator due to changing proportions between the primary and the secondary phases. Nonlinear hardening strongly increases the stress level during each serration, which affects production of the internal lattice barriers, and the amount of the accumulated plastic strain. This, in turn, affects intensity of the phase transformation (full coupling). The constitutive model and its numerical version allow to reproduce the observed serrations, which is crucial for its application in the design of components operating at extremely low temperatures.

Słowa kluczowe:

multiscale constitutive model, discontinuous plastic flow, strain induced phase transformation, cryogenic temperatures

Afiliacje autorów:

Streszczenie:

Evolution of micro-damage in the course of discontinuous plastic flow (DPF, serrated yielding) at extremely low temperatures is investigated. DPF is observed in many metals and alloys loaded in cryogenic conditions, within the temperature range specific of a given material and starting practically at absolute zero. The appearance of DPF is similar to dynamic strain ageing, however, its origin is attributed to the mechanism of local catastrophic failure of lattice barriers under the stress fields related to edge dislocation pile-ups. Failure of barriers, occurring in weakly excited lattice, leads to dynamic and massive motion of released dislocations. The phenomenon is accompanied by step-wise increase of the strain rate and drastic drop of stress during each serration. DPF has strong thermodynamic background consisting in the fact, that the plastic power dissipated in the course of serrations is partially converted to heat, which results in a local jump of temperature. It results from the so-called thermodynamic instability associated with vanishing specific heat when the temperature tends to absolute zero. The evolution of micro-damage affects loading and unloading moduli during each serration. This, in turn, results in gradual evolution of the amount of plastic slip accompanying each serration. The physically based constitutive model describes damage affected serrated yielding at the temperatures close to absolute zero. The model accounts for the thermodynamic background, including phonon mechanism of heat transport. Experimental identification of parameters of the constitutive model has been carried out based on a number of loading/unloading traction tests. A comparison between the experimental and the numerical results is presented and discussed.

Słowa kluczowe:

Multiscale constitutive model, Discontinuous plastic flow, Microstructures radiation induced damage, Cryogenic temperatures

Afiliacje autorów:

Streszczenie:

The phenomenon of strain localization in the course of discontinuous plastic flow (DPF) at extremely low temperatures is investigated. DPF is observed mainly in fcc metals and alloys strained in cryogenic conditions, practically down to absolute zero. These materials undergo at low temperatures a process similar to dynamic strain ageing, manifested by the so called serrated yielding (DPF). DPF is attributed to the mechanism of local catastrophic failure of lattice barriers (including Lomer–Cottrell locks), under the stress fields related to the accumulating edge dislocations. Failure of LC locks leads to massive motion of released dislocations, accompanied by step-wise increase of the strain rate (macroscopic slip) and drastic drop of stress. Recent experiments indicate strong strain localization in the form of shear bands propagating along the sample. The plastic power dissipated in the shear band is partially converted to heat, which results in a local drastic increase of temperature promoted by the so-called thermodynamic instability (nearly adiabatic process). The Dirac-like temperature function is measured by two thermometers located in the gage length of the sample. Spatio-temporal correlation indicates smooth shear band propagation, as long as the process of phase transformation remains on hold. A physically based multiaxial constitutive model presented in the paper describes both DPF and strain localization, accompanied by temperature distribution represented by Green-like solution of heat diffusion equation. The model accounts for the thermodynamic background, including phonon mechanism of heat transport, accompanied by specific heat vanishing with the temperature approaching absolute zero. Experimental identification of parameters of the constitutive model is carried out. A projection of the model to the range where the phase transformation takes place is discussed.

Słowa kluczowe:

Multiscale constitutive model, Discontinuous plastic flow, Cryogenic temperatures, Strain localization

Afiliacje autorów:

Streszczenie:

This paper presents the dynamic analysis of clip-on extensometer–specimen structure subjected to uniaxial tensile tests. The dynamic behavior of such structure is influenced by vibrations that can be caused by external factors, such as vibrations carried by the tensile test machine, “cold-welding” effect (typically at ultra-low temperatures) or internal factors arising from the plastic instability of testing materials. The Portevin–Le Chatelier effect (PLC), discontinuous plastic flow phenomenon (DPF) or Lűders band propagation effect are the most prominent modes of plastic deformations, that are characterized by an oscillatory behavior (plastic instability). Both factors are included in our analysis.

Słowa kluczowe:

Clip-on extensometer, Dynamic analysis, Tensile testing, Cryogenic temperatures

Afiliacje autorów:

Streszczenie:

FCC metals and alloys are massively used in cryogenic applications down to the temperature of absolute zero, because of suitable physical and mechanical properties including high level ductility. Many of these materials undergo at low temperatures a process similar to dynamic strain ageing, reflected by the so-called discontinuous plastic flow (DPF, serrated yielding). The physically based multiaxial constitutive model presented in the paper constitutes a generalization of the previous uniaxial model that proved efficient in describing the plastic flow instabilities occurring at extremely low temperatures. The model takes into account thermodynamic background, including the phonon mechanism of heat transport and thermodynamic instability caused by specific heat vanishing with the temperature approaching absolute zero. The DPF is described by the mechanism of local catastrophic failure of lattice barriers (for instance Lomer-Cottrell locks) under the stress fields related to the accumulating edge dislocations. The failure of LC locks leads to massive motion of released dislocations accompanied by step-wise increase of the strain rate (macroscopic slip). In the present paper the plastic flow discontinuity associated with the proportional loading paths is studied. Identification of parameters of the constitutive model is based on the experimental data collected during several campaigns of tensile tests carried out on copper and stainless steel samples immersed in liquid helium (4.2 K).

Słowa kluczowe:

Multiscale constitutive model, Discontinuous plastic flow, Cryogenic temperatures, Multiaxial loads

Afiliacje autorów:

Słowa kluczowe:

Deformation-induced martensitic transformation, Austenitic Stainless Steel, Additive Manufacturing, DIC, Cryogenic temperatures

Afiliacje autorów:

Słowa kluczowe:

Phase transformation, Deformation-induced martensitic transformation, 316L, Fused Deposition Modelling

Afiliacje autorów: